Container Deployment Using humio (Testing Only)

Important

The humio is not recommended or supported for use in production deployment and should be used for development and testing only. For a production deployment, see Container Deployment Using humio-core or LogScale Deployment using Kubernetes. For more information on the reference architecture for a Kubernetes deployment, see LogScale Kubernetes Reference Architecture.

To deploy LogScale using Docker:

  1. The first step to installing LogScale using Docker is to install Docker on the machine where you want to run Docker with LogScale. You can Download Docker from their site or by using a package installation program like yum or apt-get.

  2. Once you have Docker installed, you'll need to create a LogScale configuration file on the host machine. This should define basic settings such as the hostname and port numbers that LogScale will use. For example, when using the humio container you might use the following configuration file called .env:

    ini
    AUTHENTICATION_METHOD=none
    
    ELASTIC_PORT=9200
    
    PUBLIC_URL=http://localhost:8080
    
    KAFKA_SERVERS=127.0.0.1:9092
    HUMIO_PORT=8080
    
    HUMIO_SOCKET_BIND=0.0.0.0
    HUMIO_HTTP_BIND=0.0.0.0

    This sets the public URL to be on port 8080, use the embedded Kafka service and listen on the default IP address.

    For other configuration values, see Basic Configuration and LogScale Configuration Parameters.

    Note

    Docker only loads the environment file when the container is initially created. If you make changes to the settings in your environment file, restarting the container won't work. You'll need to execute docker rm with the container name, and then execute docker run for the changes to take effect.

  3. Now, make two directories on the host machine: one to store data for LogScale in general and one for Kafka data. And then pull the latest LogScale image by executing the following at the command-line:

    shell
    $ docker pull humio/humio

    Separate mount points help isolate Kafka from the other services since Kafka may consume large amounts of disk space. By placing the LogScale data and Kafka data on different volumes, this mitigats filling up the volumes. If the LogScale installation does run out of disk space and gets into a bad state, recovery instructions can be found in Switching Kafka.

    For information on updating LogScale, see Updating LogScale.

Starting Docker with LogScale

Once Docker and the humio image have been downloaded and the LogScale configuration file set, You are ready to run the LogScale Docker image as a container.

shell
$ docker run -v $HOST_DATA_DIR:/data  \
   --net=host \
   --name=humio \
   --ulimit="nofile=250000:250000"  \
   --stop-timeout 300 \
   --env-file=$PATH_TO_CONFIG_FILE humio/humio

To customise the configuration:

  • Replace $HOST_DATA_DIR with the path to the mounts/data directory for the data on the host machine.

  • Replace $PATH_TO_CONFIG_FILE with the path of the configuration file you created

  • The directory $PATH_TO_READONLY_FILES provides a place to put files that LogScale needs at runtime, such as certificates for SAML authentication.

At this point, LogScale should be running. Using a web browser, navigate to http://localhost:8080 to open the LogScale user interface. However, there are a first of the settings above that you might adjust further based on how you're using LogScale with Docker.

Some additional considerations:

  • If you're running the LogScale containers with a host that's using SElinux in enforcing mode, the container has to be started with the --privileged flag set.

  • In the example above, the LogScale container was started with full access to the network of the host machine (--net=host). Another possibility is to forward explicit ports: -p 8080:8080. By default LogScale only uses port 8080.

  • On a macOS machine, there can be problems with using the host network (i.e., --net=host). If that happens, use -p 8080:8080 to forward port 8080 on the host network to the Docker container.

  • You may also need to allow enough memory for the virtual machine running Docker on Mac. Open the Docker app, go to preferences, and specify 4GB.

Running LogScale as a System Service

The Docker container can be started as a service using the Docker run reference.

To ensure LogScale restarts, add --detach and --restart=always to the above Docker run:

shell
$ docker run ... --detach --restart=always